Description
Kenwood KAC-9106D 2000W Monoblock Class D Car Audio Power Amplifier
Kenwood makes tough, rugged amplifiers that bring you superior sound quality along with reliable performance. When you power your subwoofer with Kenwood's Performance Series KAC-9106D amplifier, you'll hear all the great tonal color, impact, and detail in your music's bass, from the hard punch of the rhythm section to the soft thump of a quiet kick drum.The KAC-9106D mono amp puts out up to 1,000 watts RMS to your subwoofer. Onboard low-pass and subsonic filters let you adjust the signal so you'll get the best sound possible from your subwoofer/box combo.
Product highlights:
- Mono subwoofer amplifier
- 500 watts RMS x 1 at 4 ohms (1,000 watts x 1 at 2 ohms)
- CEA-2006 compliant
- Class D amp design
- Variable low-pass filter (50-200 Hz at 24 dB per octave)
- Bass boost (0-18 dB at 40 Hz )
- Subsonic filter (20-50 Hz, 18 dB/octave )
- Speaker-level inputs with signal sensing turn-on
- Preamp inputs and outputs
- Fuse rating: 40A x 3
- 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- 13-3/16"W x 2-1/4"H x 7-5/8"D
- Warranty: 1 year
- Our 30-day money-back guarantee
- MFR # KAC-9106D
Gain: To accommodate the varying range of signal levels from today's factory and aftermarket radios, the KAC-9106D features an adjustable gain control; 0.2-5.0 volts line level (RCA) and 4.0-12.0 volts speaker level.
Crossover: The built-in 24 dB/octave low-pass filter has a continuously variable crossover point; 50Hz to 200Hz. Because this is a subwoofer amp, the crossover is always engaged.
Infrasonic Filter: The 24 dB/octave Infrasonic Filter removes ultra-low frequencies that cannot be reproduced by most subwoofers. These frequencies do not become sound, but unnecessary oscillations which affect sound by causing distortion. These frequencies also waste amplifier power and can cause damage to speakers. The filter's crossover point is continuously variable from 20 Hz to 50 Hz.
Bass Boost: The bass boost is adjustable from 0-18dB at 40Hz.
Kenwood KAC-9106D - Reliable performer
Kenwood makes tough, rugged amplifiers that bring you superior sound quality along with reliable performance. When you power your subwoofer with Kenwood's Performance Series KAC-9106D amplifier, you'll hear all the great tonal color, impact, and detail in your music's bass, from the hard punch of the rhythm section to the soft thump of a quiet kick drum.
CEA-2006 Compliant:
CEA-2006 is a system of testing and measurement for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4Ω load, with 1% or less Total Harmonic Distortion plus noise (THD+N), and over a frequency range of 20 Hz to 20 kHz (for full range amplifiers). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4Ω. CEA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples). Using CEA-2006 criteria, the Kenwood KAC-9106D is rated at 500 watts RMS x 1 channel with a 76 dBA signal to noise ratio. The signal to noise ratio at the rated power output (not CEA-2006 conditions) is 100 dB.
Connections:
Power Connections: The power and ground connections are 0.55" wide screw terminals. The remote turn-on screw terminal is 0.335" wide. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are recommended. The manual lists a minimum of 10 gauge wire for power and ground, but given the 120 amp fuse value and the current consumption specification of 65 amps, we recommend a 4 gauge wiring kit.
Speaker Outputs: There are two pair of 0.335" wide screw terminal speaker outputs; they are internally wired in parallel, making it easy to connect two subwoofers. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are also recommended for the speaker wires.
Controls:
Gain: To accommodate the varying range of signal levels from today's factory and aftermarket radios, the KAC-9106D features an adjustable gain control, 0.2-5.0 volts line level (RCA) and 4.0-12.0 volts speaker level.
Crossover: The built-in 24 dB/octave low-pass filter has a continuously variable crossover point, 50Hz to 200Hz. Because this is a subwoofer amp, the crossover is always engaged.
Bass Boost: The bass boost is adjustable from 0-18dB at 40Hz.
Additional Information
Shipping & Return
Reviews
My Wishlist
Wishlist is empty.
Compare
Shopping cart
